![]() ![]() ![]() Tx>Rx Rx>Tx 5v and all grounds connected. I'm afraid none of this helps very much, you are essentially doing the right thing, and all I can suggest is to check the wiring: Blink 182 (Vitamin C Remix) is Vitamin Cs remix of Half an Oranges original track Blink 182, released on August 22, 2020. The six-pin boards are probably old stock they are using up, and they were originally made for the HC-05. I assume yours is pretty new, and I guess they will all be like that eventually. While your ZS-040 has only four pins, that is all it really needs. This implies that, while the command set is like the HC-05, the procedure is about the same as an HC-06. if it isn't talking to something, you just send AT commands. There is no special procedure for configuring the HM-10. I have looked a bit further into this and have concluded that This also goes quite some way to explain why I don't know anything about that USB thing either. I didn't say it can't be connected, I said I don't know anything about it, and can't comment. I beg to disagree that it can't be connected in serial monitor or teraterm.īased on the description of the HM10 module, it can be configured as Master/Slave and can use AT command to set the baudrate That doesn't mean the power is reliable, and if you have a 5v supply you should stick with it, particularly when the board says 3.6v minimum If you see a LED, that means there is power. If you don't have 5v on the ZS-040 already, you may be able to get it from the USB thingy.įirst I tried 3.3V, but when I notice the backboard voltage requirement, I changed it to 5V.īoth voltages blinks the ZS-040 power LED. I know nothing about that and can't comment, but I suggest you confirm the power supply is kosher. I get the impression you are not using an Arduino to configure it, but merely the Arduino programming software. I know nothing about that USB device in the picture. ![]() The standard way to power these things when using an Arduino to configure it is thus from the 5v pin on Arduino. Yes the HM-10 is a 3.3v device, but the ZS-040 has on-board regulators and you will see it marked 3.6>6v on the back. The reason why you are not getting any joy may simply be the power supply. Swagtron Swagboard Twist T882 Hoverboard Overall Score: 8.8 6. SISIGAD Bluetooth Speaker 6.5-Inch Hoverboard, Matte White Overall Score: 9.0 5. Most Commonly Compared to BlinkSwag vs Enable Blackline Safety G7 MARMIND VCV Inc. XPRIT Bluetooth Speaker Hoverboard, Black Overall Score: 9.2 4. TOMOLOO Music-Rhythmed LED Light Hoverboard, Black Overall Score: 9.9 3. In the light of this, and despite what I said, I believe you should steer clear of tutorials that address the HC-05. Hover-1 Helix Electric Hoverboard, Galaxy Overall Score: 10.0 2. I see my HM-10 on ZS-040 has no button switch, while the HC-05 does. no procedure is required to get it into AT mode, hence only four pins and no button switch. You may find that the HM-10 is in AT mode whenever it is not actually communicating to another device, i.e. It could be be that using only four pins is entirely legitimate and, while mine and every other HM-10 I have seen is on a backboard with six pins, at least one of them is redundant. It appears that that article only uses four pins to configure. Fast Charger (45 min) is available under “Accessories” via ACTON online store.The tutorial I referring only use those pins when using AT commands.With a 5.5 hour charge time, you can travel up to 5. Heavier weight, hills, and bumpy surfaces with pro mode will reduce the range. Break the rules of hoverboarding and conquer the streets with the lithium-free SWAGTRON T8 self balancing scooter. Note: Blink Lite can travel 5 miles on a full charge - this range is tested under ideal conditions with average weight, smooth, level surfaces in beginner mode. Lithium Ion 25.5V, 2.2AhěATTERY Lithium Ion 36V, 2Ah, 10Cģ1” x 11” x 7” PACKAGE DIMENSIONSĒ9” x 13” x 8” Polyurethane, 70mm, 78A Hardness WHEEL TYPE Polyurethane, 83mm, 78A Hardness Here are the specs- My question is should I refund it or are these materials worth a lot from my DIY build, coming soon. Usually $400 I bought it for $300 New, authentic and everything. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |